Product informations - PNZ-HARD-WAX-OIL
Properties:
PNZ-HARTWACHS-ÖL (PNZ-HARD-WAX-OIL) is an open-pored, moisture regulating, colourless, professional surface coating product for wood and cork, strongly water repellent, resilient against common foodstuffs and household chemicals acc. to DIN 68861. -1C.
The coat is safe for humans, animals and plants after drying and complies with DIN 53160 and EN 71 for children?s toys. Contains no biocidal substances and preservatives, excellent cover power. Also available in white.
Areas of use:
For all heavily used interior areas, such as wooden floors, cork, OSB boards, wood composites, worktops, furniture, terracotta and unglazed tiles, also in damp rooms such as the bathroom and kitchen. Well suited for children?s nurseries, hospitals etc.
Usage:
Colourless or white PNZ-HARTWACHS-ÖL can be applied manually or mechanically. The moisture content of the wood should not be more than 15%. Surfaces must be clean, free of grease and, if required, sanded. Repair holes and cracks with PNZ Repair paste.
Manual application:
Apply the first coat thinly with a paintbrush or trowel, remove after approx. 10 minutes until the surface appears dry, rub in with a pad as required. Allow to dry for 8-10 hours (overnight) with good ventilation. Repeat the second coat as the first; do not allow any excess to remain. For white PNZ-HARTWACHS-ÖL, we definitely recommend a third coat of colourless PNZ-HARTWACHS-ÖL as protection against the abrasion of the pigments, applied as previously described. The surface can be polished over with a white pad PNZ-SINGLE-DISC-POLISHER or PNZ-PFLEGEBOY (suction wax polisher).
Mechanical application:
Pour small quantities of PNZ-HARTWACHS-ÖL at points over the wooden surface, then rub in evenly by brush or single disc polisher until the surface appears dry (allow no excess to remain). Repeat the process after approx. 8-10 hours. The surface can then be walked upon after approx. 12 hours. This increases the resistance to wear. Wooden floorboards can also be treated individually prior to being laid. Complete drying time approx. 8-10 days. Do not lay a carpet before this time. Do not apply under a temperature of + 8°C. Afterwards it can be cleaned with PNZ-HOLZBODENSEIFE (PNZ-WOOD-FLOOR-SOAP) and maintained with PNZ-PFLEGEEMULSION (PNZ-CARE-EMULSION). Simple renovation of heavily used or damaged areas. Clean with PNZ-GRUNDREINIGER (PNZ-DEEP-CLEANER), cover with PNZ-HARTWACHS-ÖL. It is not necessary to sand surfaces to be repaired.
It has different effects on different surfaces. Trial coats are therefore essential.
Care:
Dry brush, wipe with a sprayed damp mop or vacuum, e.g. with a suction wax polisher PNZ-PFLEGEBOY (suction wax polisher). In the case of severe soiling, add PNZ-HOLZBODENSEIFE (PNZ-WOODEN-FLOOR-SOAP) to the water. Use PNZ-PFLEGEEMULSION (PNZ-CARE-EMULSION) or PNZ-WACHSFINISH (PNZ-WAX-FINISH) for after care.
Coverage:
Up to 20 sqm. and more per litre per coat depending on the surface and wood type.
For cross-grained wood and strongly absorbing woods, such as beech, we recommend three applications, as described above.
Cleaning:
Clean tools with PNZ-SPEZIALVERDÜNNUNG (PNZ-SPECIAL-THINNER) or white spirit.
Contents:
Isoaliphates, natural plant oils and waxes, such as sunflower oil and rapeseed oil from controlled domestic cultivation, safflower oil, soya oil, shellac wax, candelilla wax, carnauba wax, microwax and lead-free drying agents, for White: titan white.
Note:
When using several containers with different lot numbers, they should be mixed together in a large container!
VbF (German regulations on combustible liquids): A III
Store soaked cloths in closed containers or soak in water (danger of spontaneous combustion).
The dried coat is highly flammable as defined by TLA-053 and normal acc. to DIN 4102 B2. UBA 26010014
Container sizes:
0.75 litres, 2.5 litres, 10 litres, 30 litres and larger.
|
